Plumbing 101: What You Must Have for Bathtub Installation
Plumbing 101: What You Must Have for Bathtub Installation
Blog Article
What are your opinions about How to Install a Bathtub?
Installing a bathtub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a brand-new one is also a moderately hard task. If the old bathtub is readily accessible, the job can move immediately; if you need to open a wall surface to get rid of the old bathtub and also position the new bathtub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and set in the new one. Make sure you have actually certified yourself for the work and also are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This article will aid you set up a brand-new bath tub in your shower room if you have already gotten a new tub and do not require to change the plan of your previous water pipelines.
Your tools and also material checklist need to comprise the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the limited access that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Prior to proceeding to fit the new taps, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in area in between the faucet and the sink. Protect the faucet in position with the producer offered backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The former kind needs to be linked to the faucet ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Utilizing both wooden boards under its feet, place the bath tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the level checks out level.
To install faucets, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill the tub as well as also examine the overflow electrical outlet as well as the regular outlet for leaks.
Finally, take care of the bath paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bath tub must wait up until the tub has actually been used at least once as this will resolve it right into its final setting.
Planning for the Installment
First of all, the supporting framework supplied with the bath must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets device to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must now prepare to be suited its final placement.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a rigid seal, triggering the water to penetrate the wall surface in between the bathroom as well as the tiling, causing issues with moisture as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the movement experienced when the tub is in usage. The sealant can split fairly very early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily offered on the market. It is recommended to fit the ceramic tiles using water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that article on Installing A Bathtub from an acquaintance on our other web blog. Those who appreciated our post plz be sure to pass it around. We treasure reading our article about Installing A Bathtub.
We've got this! Report this page